[Rhodes22-list] Stove - Question on How to slide it out

[Arthur H. Czerwonky]

Jim,

Are you sure? You should be able to wiggle cannister and stove into a void under the stove.  Like Rummy suggested, that picture will be worth a thousand, even snapshots from different angles.  Why cut a recess in the counter if you aren't meant to use it?  Your action team is ready...

Art

-----Original Message-----
>From: jimjim02 <jamesldickson at aol.com>
>Sent: Aug 6, 2009 1:21 PM
>To: rhodes22-list at rhodes22.org
>Subject: Re: [Rhodes22-list] Stove - Question on How to slide it out
>
>
>Thanks for the reply Art
>
>The Butane Caster fitting is on top of the stove which is not cut out, so I
>need to pull out the stove to install the butane can to fuel the stove.
>
>Jim
>
>
>
>
>
>Arthur H. Czerwonky wrote:
>> 
>> Jim,
>> 
>> You refer to the butane stove, which has been recessed into the counter
>> top, I assume.  Why pull it out, unless you risk close exposure with an
>> inflammable surface, which should not be true in any factory installation. 
>> The stove cannister 'receiver' should be keyed, just like the cannister is
>> itself.  If not aligned, you will not have a torch, and consequently will
>> have cold dinner.  Now then, some summer meals are better cold, so just
>> develop a liking for tuna salad...
>> 
>> Art
>> 
>> 
>> -----Original Message-----
>>>From: jimjim02 <jamesldickson at aol.com>
>>>Sent: Aug 6, 2009 12:11 PM
>>>To: rhodes22-list at rhodes22.org
>>>Subject: [Rhodes22-list]  Stove - Question on How to slide it out
>>>
>>>
>>>Hi Everyone
>>>Can someone tell me how the the Portable Stove is used. I'm assuming you
>>>have to pull it out and place it on the counter to use. For pulling it out
>I
>>>see there is a cotter ring right in front to pull out.
>>>
>>>Is there any additional rings or screws that need to be taken out or
>>>loosened before trying to slide it out.
>>>
>>>When I pull the front cotter ring out and try to slide it out it doesn't
>>>move just don't want to force it out and break it. Want to make sure I get
>>>all the screws necessary to pull it out.
>>>
>>>Any help would be greatly appreciated.
>>>
>>>Thanks Jim
>>>-- 
>>>View this message in context:
>http://www.nabble.com/Stove---Question-on-How-to-slide-it-out-tp24849591p24849591.html
>>>Sent from the Rhodes 22 mailing list archive at Nabble.com.
>>>
>>>__________________________________________________
>>>To subscribe/unsubscribe go to
>http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>>>
>>>For the list Charter and help with using the mailing list and archives go
>to http://www.rhodes22.org/list
>>>__________________________________________________
>> 
>> __________________________________________________
>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>> 
>> For the list Charter and help with using the mailing list and archives go
>> to http://www.rhodes22.org/list
>> __________________________________________________
>> 
>> 
>
>-- 
>View this message in context: http://www.nabble.com/Stove---Question-on-How-to-slide-it-out-tp24849591p24850902.html
>Sent from the Rhodes 22 mailing list archive at Nabble.com.
>
>__________________________________________________
>To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>
>For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list
>__________________________________________________