[Rhodes22-list] portholes part 2

[Goodness]

Good point!  I just bedded a dozen bronze ports in a steel hulled 43' ocean going cutter and used 5200.  When and if i redo the job i will grind it off with a grinder and wire brush.  Permanance was my plan. :-)  For plastic hulls 4200 is a better choice.



On Sep 10, 2012, at 7:33 PM, Rick <sloopblueheron at gmail.com> wrote:

> 3M 4200 would be the better choice.  3M 5200 is for permanent joins and if
> a lens cracks, you'll never be able to replace the port.
> 
> Rick
> 
> On Mon, Sep 10, 2012 at 5:31 PM, Goodness <spreadgoodnews at gmail.com> wrote:
> 
>> If you bed the metal ports in 5200 properly curvature is a non-issue.
>> Also new plastic ports will bend to the curve, the old ones just have this
>> curve set into them.
>> 
>> 
>> 
>> On Sep 10, 2012, at 11:27 AM, John Lock <jlock at relevantarts.com> wrote:
>> 
>>> Keep in mind that those ports are not all the same.  One set (I can't
>>> remember if it's the aft pair or the forward pair) have a very slight
>>> curvature in the base to match the slight curve of the cabin at that
>>> point.  If you just replace it with a straight base the seal will not be
>>> well made and it will leak.
>>> 
>>> --
>>> Cheers!
>>> John Lock
>>> ~~~~~~~~~~~~~~~~~~
>>> s/v Pandion - '79 Rhodes 22
>>> Lake Sinclair, GA
>>> ~~~~~~~~~~~~~~~~~~
>>> 
>>> 
>>> On 2012-09-09 17:49, Ejor2 wrote:
>>>> I broke most of mine trying to get them out so I replaced them all. Got
>> them from Beckson on clearance for around 45 apiece. My Boat is an 80, so
>> not sure if size of opening is the same.
>>>> 
>>>> Eric J
>>>> 
>>>> 
>>>> 
>>>> On Sep 9, 2012, at 12:59 PM, Bill Pauer <billpauer at gmail.com> wrote:
>>>> 
>>>>> I got five of the six ports out in one piece, but I managed to break
>>>>> the fifth one.  Does anyone know the brand  of the Rhodes original
>>>>> ports (1985 model) and where I might find them online?  I am also
>>>>> considering adding one of the larger hatches which the newer Rhodes
>>>>> have.  Has anyone tried to install one of these themselves?  What
>>>>> model is General Boats using?
>>>>> 
>>>>> Thanks again,
>>>>> Bill
>>>>> __________________________________________________
>>>>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>>>>> 
>>>>> For the list Charter and help with using the mailing list and archives
>> go to http://www.rhodes22.org/list
>>>>> __________________________________________________
>>>> __________________________________________________
>>>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>>>> 
>>>> For the list Charter and help with using the mailing list and archives
>> go to http://www.rhodes22.org/list
>>>> __________________________________________________
>>>> 
>>>> 
>>> 
>>> 
>>> __________________________________________________
>>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>>> 
>>> For the list Charter and help with using the mailing list and archives
>> go to http://www.rhodes22.org/list
>>> __________________________________________________
>> 
>> __________________________________________________
>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>> 
>> For the list Charter and help with using the mailing list and archives go
>> to http://www.rhodes22.org/list
>> __________________________________________________
>> 
> __________________________________________________
> To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list
> 
> For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list
> __________________________________________________