[Rhodes22-list] Covert Badlands 2500 Winch from remote to rocker switch?

[Hank]

Also, you may not need a 30 amp rated switch or fuse where you have it in
your drawing, but you do need to have the power to the motor go through an
appropriate circuit breaker or fuse to protect the motor from burning up
should you have an issue.

On Tue, Jun 18, 2019 at 8:47 PM Mike Riter <mike at traildesign.com> wrote:

> Ha! Yup. I'll correct the drawing. Thanks for catching that Hank.
>
> Michael Riter
> President, Trail Design Specialists, Inc.
> Lead Instructor, Trail Master and mechanized training
> mike at traildesign.com
> 678-410-8021
>
>
>
> On Tue, Jun 18, 2019 at 5:07 PM Hank <hnw555 at gmail.com> wrote:
>
> > Hey Mike,
> >
> > Hopefully not a dumb question, but it looks like you have the relay coils
> > both going to the same contact on the motor.  Wouldn't they need to go to
> > opposite contacts to reverse the direction of the motor?
> >
> > Hank
> >
> > On Tue, Jun 18, 2019 at 6:04 PM Mike Riter <mike at traildesign.com> wrote:
> >
> > > No worries Bob.
> > > I was just looking at my drawing and realized you don’t need a 30 amp
> > rated
> > > switch since the switch is only powering the relay coils. I would
> > recommend
> > > the best water tight, marine grade switch you can get that’s rated for
> a
> > > few amps higher than either of the relays.
> > >
> > > On Tue, Jun 18, 2019 at 4:07 PM Bob Garrant <bgarrant at gmail.com>
> wrote:
> > >
> > > > Mike,
> > > > The attachment came through. Very helpful. And just in time because
> the
> > > > remote seems like it’s about to ‘expire’.
> > > > Thanks very much,
> > > > Bob
> > > >
> > > >
> > > > On Tue, Jun 18, 2019 at 4:13 PM Mike Riter <mike at traildesign.com>
> > wrote:
> > > >
> > > > > The switch needs to go through isolation relays to prevent back
> > feeding
> > > > the
> > > > > system. The relays should already be there. You'll need to remove
> the
> > > > > wireless control and wire a SPDT switch rated for at least 30 amps
> in
> > > its
> > > > > place. I put together a drawing showing how it should be wired.
> > > > >
> > > > > Michael Riter
> > > > > President, Trail Design Specialists, Inc.
> > > > > Lead Instructor, Trail Master and mechanized training
> > > > > mike at traildesign.com
> > > > > 678-410-8021
> > > > >
> > > > >
> > > > >
> > > > > On Tue, Jun 18, 2019 at 2:10 PM Peter Nyberg <
> peter at sunnybeeches.com
> > >
> > > > > wrote:
> > > > >
> > > > > > The attachment came through for me.  The link is at the very
> bottom
> > > of
> > > > > the
> > > > > > message.
> > > > > >
> > > > > > Peter Nyberg
> > > > > > Coventry, CT
> > > > > > s/v Silverheels (1988/2016)
> > > > > >
> > > > > >
> > > > > >
> > > > > > > On Jun 18, 2019, at 2:47 PM, Mark West via Rhodes22-list <
> > > > > > rhodes22-list at rhodes22.org> wrote:
> > > > > > >
> > > > > > > sorry the attachment did not go?
> > > > > > >
> > > > > > >
> > > > > > > -----Original Message-----
> > > > > > > From: Mark West via Rhodes22-list <rhodes22-list at rhodes22.org>
> > > > > > > To: rhodes22-list <rhodes22-list at rhodes22.org>
> > > > > > > Sent: Tue, Jun 18, 2019 2:34 pm
> > > > > > > Subject: Re: [Rhodes22-list] Covert Badlands 2500 Winch from
> > remote
> > > > to
> > > > > > rocker switch?
> > > > > > >
> > > > > > > I would remove the remote system, then rewire manual switch 1
> > > system
> > > > > > could back feed other and let the magic blue smoke out. mine
> needed
> > > 30
> > > > > amp
> > > > > > fuse I think this attachment is how I wire it  Mark s/v Fairwind
> 2
> > > > > > > -----Original Message-----
> > > > > > > From: Bgarrant <Bgarrant at gmail.com>
> > > > > > > To: rhodes22-list <rhodes22-list at rhodes22.org>
> > > > > > > Sent: Tue, Jun 18, 2019 10:20 am
> > > > > > > Subject: [Rhodes22-list] Covert Badlands 2500 Winch from remote
> > to
> > > > > > rocker switch?
> > > > > > >
> > > > > > > I want to convert the Badlands 2500 Winch Motor for my motor
> lift
> > > > from
> > > > > a
> > > > > > > wireless remote to a rocker switch. I would appreciate guidance
> > for
> > > > > doing
> > > > > > > this. It seems pretty straightforward but maybe I’m overlooking
> > > > > > something.
> > > > > > > Thanks,
> > > > > > > Bob Garrant
> > > > > > > s/v Sail la Vie 2000
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > --
> > > > > > > Sent from: http://rhodes-22.1065344.n5.nabble.com/
> > > > > > > -------------- next part --------------
> > > > > > > A non-text attachment was scrubbed...
> > > > > > > Name: Untitled.png
> > > > > > > Type: image/png
> > > > > > > Size: 26970 bytes
> > > > > > > Desc: not available
> > > > > > > URL: <
> > > > > >
> > > > >
> > > >
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20190618/b39bb15c/attachment.png
> > > > > > >
> > > > > > > -------------- next part --------------
> > > > > > > A non-text attachment was scrubbed...
> > > > > > > Name: switch.png
> > > > > > > Type: image/png
> > > > > > > Size: 26970 bytes
> > > > > > > Desc: not available
> > > > > > > URL: <
> > > > > >
> > > > >
> > > >
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20190618/984ca6e7/attachment.png
> > > > > > >
> > > > > >
> > > > > >
> > > > > -------------- next part --------------
> > > > > A non-text attachment was scrubbed...
> > > > > Name: SPDT reversible switch.jpg
> > > > > Type: image/jpeg
> > > > > Size: 599311 bytes
> > > > > Desc: not available
> > > > > URL: <
> > > > >
> > > >
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20190618/f5cc30a3/attachment.jpg
> > > > > >
> > > > >
> > > >
> > > --
> > > Michael Riter
> > > President, Trail Design Specialists, Inc.
> > > Lead Instructor, Trail Master and mechanized training
> > > mike at traildesign.com
> > > 678-410-8021
> > >
> >
>