[Rhodes22-list] Trailer winch
PBR
pbryanriley at gmail.com
Thu Nov 19 13:35:12 EST 2026
Sounds like we all have similar issues.
Back to the ? about the winch slipping. I have not seen that . All my
winches (except on for mast raising) have mechanical gears that are
visible. One has a missing tooth and it does skip at that point. You
might have a case of a really loose wound strap that might appear to slip
when it tightens up. Or, maybe should unwind it all the way and make sure
the "bitter end" is still attached to the winch wheel.
On moving the boat forward. I have steep ramps that exacerbate the
problem. I have considered moving the axle or the winch post. Before I do
that I might try some nylon or plastic "boat glides" just screwed over top
of my outdoor carpet (very not slick) covering on the bunks to reduce
friction and allow more forward winching. Also, my bunks are not
contacting the boat full length and having most of the contact near the
ends might cause more friction, IDK. I intend to adjust those next time I
have the boat off the trailer for any length of time.
Patrick
On Thu, Nov 19, 2026 at 12:09 PM Graham Stewart <graham at debgraham.ca> wrote:
> I have always found that I have been unable to to get the boat
> sufficiently forward. Ontario one occasion the boat started to sway
> severely. I was very lucky that it occurred on a multi lane highway when
> there was no traffic.
> I only tow the boat from my home to the boat launch about 5 miles at low
> speed so I am not concerned However, should I ever take it on a longer
> trip I would redistribute weight by moving the motor to the car and moving
> anything that is heavy like the gas tank forward in the boat.
>
> > On Nov 18, 2026, at 11:24 AM, Mary Lou Troy via Rhodes22-list <
> rhodes22-list at rhodes22.org> wrote:
> >
> > It is awkward to pull it out incrementally but we were very successful
> doing it that way for the 18 years we owned the R22.
> >
> > Our method was to pull it forward until there was slack which if pulled
> further would allow the boat to slip back. At that point we paused and
> winched up the slack. We would do this however many times it took to get
> the boat to the right point. We had the bow stop piece marked with some
> paint so we knew exactly where we wanted to boat for the right tongue
> weight. We found that the process varied somewhat from ramp to ramp but we
> got so used to it that it only took a few minutes longer than if we had
> been able to winch it all the way forward.
> >
> > Mary Lou
> >
> >> On 11/18/2026 10:34 AM, peter beckerman via Rhodes22-list wrote:
> >> Thanks to all for your thoughts, My recovery procedure: With the
> trailer in the water to the top of the bunks and the bow crutch slid all
> the way forward I winch the boat fully to the crutch. Then as I pull the
> trailer out of the water and the boat settles on the bunks it pivots back
> too far away from the crutch. I’m trying to move the hull 6-12 more inches
> to improve tongue weight. There’s something in the manual about towing to
> about 5 mph and slamming on the brakes which I tried unsuccessfully, and I
> read somewhere (manual?) about using an old tire as a bumper and backing up
> against a tree which I have not tried (too scared). As Peter suggested
> on my next attempt I will probably try pulling the trailer out
> incrementally and winching as I go. Seems kinda awkward.
> >> Does anyone have any other tips?Also is it possible to buy too strong
> of a winch?AFAIK my winch is original (1986), but I did replace the strap!
> >> Peter
> >
>
>
More information about the Rhodes22-list
mailing list