[Rhodes22-list] Planjammers (?)-Special Request

[Roger Pihlaja]

Jay,

OK, I looked thru my entire 1991 Dwyer catalog & I came up up several
possibilities:

DH 601 Mast Eye: Looks like a HD stainless steel plate bent in 3 places to
                              approximately fit the mast curvature with a HD
stainless
                              steel ring welded to the plate.  I would use
this part for
                              a fixed spinnaker pole mount on the mast.
Uses 4X#10
                              machine screw fasteners - 2 per side

DH 602 Mast Eye: Looks like DH 601 but sized to fit a smaller mast.  The
                              DH 601 would be the one that fits an R-22
mast.

DH 312 Bail: Looks like one piece of stainless steel strap with 3 bends in
it.
                     The outer two bends are meant to fit the mast curvature
&
                     could be slightly adjusted to fit many different sized
masts.
                     The center bend section forms a U-shape like an
eyestrap.
                     Uses 4X#10 machine screw fasteners - 2 per side.

DH 856 Jib Hound: Looks like DH 312 except that, instead of the center
                               section being an eye strap, the center
section is the
                               female portion of a clevis.  Hole is sized
for 3/16" OD
                               clevis pin.  Uses 2 X 1/4" & 2 X #10 machine
screw
                               fasteners - 1 of each per side.  The 1/4"
fastener holes
                               are towards the center of the mast & appear
to be
                               intended to accept a single thru bolt which
goes right
                               thru the mast.

Jay, these were the only pieces/parts which were anywhere close to your
description.
Hope this helps.  Good luck!

Roger Pihlaja
S/V Dynamic Equilibrium





----- Original Message -----
From: "Jay Friedland" <a.jayf@verizon.net>
To: "The Rhodes 22 mail list" <rhodes22-list@rhodes22.org>
Sent: Friday, February 21, 2003 6:42 PM
Subject: Re: [Rhodes22-list] Planjammers (?)-Special Request


> Roger-
> A one-man resource center. Still working on the third halyard problem.
> I have the IMF and actually what I saw in the 99 catalog was a curved
> plate with a bullnose for mounting a block. It had 3 or 4 screwholes on
> each side for drilling into the mast. It seemed to have a three bend
> configuration to fit several curvatures. Bob's assistant didn't know
> what I was talking about and it wasn't on their website. So I didn't
> know where to go with this.
>
> I haven't had the chance to review you recommendation on dead-ending
> the topping lift, but my first take was on the 18" + drop of the boom
> on the IMF, which I use often. I need to further review, but the Dwyer
> piece was suggested by Doyle for the UPS halyard. He showed it to me,
> and I thought it would be easy to locate with Dwyer. Next time I'll
> write it down.
>
> Thanks for any help on this.
> J
>
> On Friday, February 21, 2003, at 05:55 PM, Roger Pihlaja wrote:
>
> > Jay,
> >
> > I've got a 1991 edition of Dwyer's Yellow catalog.  Each mast extrusion
> > shape & size requires a different mounting plate.  However, I'm going
> > to
> > take a wild guess as to what you probably want.
> >
> > Assuming you have the standard mast, this is a DM-500 series
> > extrusion.  The
> > DM-500 takes the D 2122H hinged step,
> > D 1015 Masthead Rig with 4 aluminum sheaves, the DH 21750L Stainless
> > Steel
> > Tabernacle, & the DH 288 Medium Halyard Organizer Plate.
> >
> > If I've guessed wrong re what you want, then you're going to have to
> > give me
> > more information in order for me to help you.
> >
> > Unfortunately, my flat bed scanner is at the repair shop, so I can't
> > send
> > you any pictures.
> >
> > Roger Pihlaja
> > S/V Dynamic Equilibrium
>
> _________________________________________________
> Use Rhodes22-list@rhodes22.org, Help? www.rhodes22.org/list
>