[Rhodes22-list] bow eye sealer, Web site, Subject line, Concrete R22

[michael meltzer]

put it this way: that type of day :-)
http://datanation.com/fallacies/index.htm

--- ed kroposki <ekroposki at charter.net> wrote:

> Peter,
> 	Thank you for mentioning this, furthermore 5200
> when it cures is
> rigid and does not flex, which could cause adjacent
> cracking or fissures.
> 
> Michael,
> 	First, how much is this going to cost? Second, give
> us a clue as to
> what you are up to.  And I thought you would be on
> LIS Saturday.  
> 	Did you follow the Crawford's trip home with their
> R22, maybe this
> fall you should sail your boat to Edenton.  You
> could use the challenge.
> 	And did you notice how Alex correctly changed his
> subject line in
> his detailed post about rail parts.  Alex gets a big
> Attaboy.
> 
> Rob,
> 	Does this mean you are building a Concrete R22?
> 
> Ed K
> Greenville, SC, USA 
> 
> 
> -Original Message-----
> From: rhodes22-list-bounces at rhodes22.org
> [mailto:rhodes22-list-bounces at rhodes22.org] On
> Behalf Of Peter Thorn
> Sent: Friday, July 22, 2005 11:05 AM
> To: The Rhodes 22 mail list
> Subject: [Rhodes22-list] bow eye sealer
> 
> Barney and Saroj,
> 
> You might want to consider GE 4200 or 3M 101 sealant
> for the bow eye  (both
> polysulfides and available at West Marine).
> Polysulfide is quite pliable and
> seals very well, but parts can be removed in the
> future.  GE 5200 is
> polyurethane and will permanently bond the bow eye
> to the hull.  If the new
> bow eye ever needed replacing again, it would be
> pretty hard to get it out.
> 
> PT
> 
> 
> 
> ----- Original Message ----- 
> From: "Saroj Gilbert" <saroj at pathfind.net>
> To: <bestpestcontrol at earthlink.net>; "The Rhodes 22
> mail list"
> <rhodes22-list at rhodes22.org>
> Sent: Friday, July 22, 2005 10:44 AM
> Subject: Re: [Rhodes22-list] Saroj
> 
> 
> > that makes a lot of sense.. thanks a bunch...
> > Saroj
> > ----- Original Message ----- 
> > From: <bestpestcontrol at earthlink.net>
> > To: "rhodes22-list" <rhodes22-list at rhodes22.org>
> > Sent: Friday, July 22, 2005 8:43 AM
> > Subject: [Rhodes22-list] Saroj
> >
> >
> > > Saroj, after removing the part or parts I took
> the nuts off the new bow
> > > eye and ran the new bow
> > > eye in and out of the holes several times to
> clean the holes out . at
> this
> > > time check to make sure it isnt moist in the
> holes--if it is moist dont
> > > put the new eye in until the holes dry out--if 
> the
> > > holes are dry I used 3M 5200 both in the
> holes(generously) and on the
> > > exterior mating surface
> > > I personally like to use too much sealant and
> wipe off the excess when
> > > done.  once you apply
> > > sealer install the new eye right away--let it
> set overnight--then
> tighten
> > > the nuts just a little more and that should do
> the job.
> > > Barney
> > >
> __________________________________________________
> > > Use Rhodes22-list at rhodes22.org, Help?
> www.rhodes22.org/list
> >
> > __________________________________________________
> > Use Rhodes22-list at rhodes22.org, Help?
> www.rhodes22.org/list
> 
> __________________________________________________
> Use Rhodes22-list at rhodes22.org, Help?
> www.rhodes22.org/list
> 
> __________________________________________________
> Use Rhodes22-list at rhodes22.org, Help?
> www.rhodes22.org/list
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com