[Rhodes22-list] R22 installing portlights and hatches

Graham Stewart gstewart8 at cogeco.ca
Tue Sep 17 16:53:37 EDT 2013


Richard:
Interesting. What about the curve of the deck? Did the hatch bend to seat or
did you need to shim it?

Graham 


-----Original Message-----
From: rhodes22-list-bounces at rhodes22.org
[mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Richard Beytagh
Sent: September-17-13 1:14 PM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] R22 installing portlights and hatches

I installed a Bomar 2000 series 16.5" x 16.5" hatch on the opposite side
from the head. Cutting the opening for the hatch was the trickiest but once
done and well siliconed up it looks great and seems to be leak proof. Be
sure to install the interior trim-strip before seating the main hatch.....I
didn't and had to re-install. BTW I found the hatch on eBay for about $80
(new they are over $500).

Richard S/Y Waif


[image: Inline image 1]

Richard
Cell: 828 337 0180


On Tue, Sep 17, 2013 at 10:45 AM, Graham Stewart <gstewart8 at cogeco.ca>wrote:

> Thanks Bob for advice on installing Beckson ports. I didn't realize 
> that they were so flexible. Does anyone know whether any hatches are 
> available that can be placed on the Rhodes deck and take the curve or 
> does the deck under the hatch need to be flattened - somehow?
>
> Many years ago I removed the original ports entirely, enlarged the 
> openings and applied a lexan cover over the three ports in one black 
> strip. It looked good but the material eventually cracked around the 
> screws because I didn't enlarge the screw holes to allow for expansion 
> and the material was too thin. The expansion over the large strip also 
> resulted in the silicone eventually leaking.
>
> The sides of the cabin have a compound curve and I am concerned that 
> thicker lexan might not be sufficiently flexible to be drawn around it 
> even if I can find a way to allow for expansion  so either I go back 
> to using ports or apply separate lexan covers for each opening. At 
> this point the latter seems most feasible and at substantially less 
> cost but I would be interested to hear from others who have addressed 
> this problem or have opinions about it.
>
>
> Graham
>
> -----Original Message-----
> From: rhodes22-list-bounces at rhodes22.org
> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of BobMellor
> Sent: September-16-13 10:10 PM
> To: rhodes22-list at rhodes22.org
> Subject: Re: [Rhodes22-list] R22 installing portlights and hatches
>
> Graham...
> I replaced mine with becksons..  The fronts were still identical, but 
> they do not make the real flexible side ones anymore...  I used the 
> ones a bit bigger, opened the holes a bit, then mounted them "inside
out"..  Thus the
> hard shell part is inside where the alignment did not matter..   Used some
> wedges where needed.  Then I trimmed the sleeve that stuck out too 
> much on the outside so they were flush with the trim rings. (The trim 
> rings bend to the contours easily.) ( need to tell them how you are 
> mounting so the put the lexan in the right way.  The folks at beckson were
reveal helpful.
>
> Bob Mellor
>
>
>
> --
> View this message in context:
>
> http://rhodes-22.1065344.n5.nabble.com/List-Etiquette-was-Re-availabil
> ity-of
> -130-genoas-tp46689p46783.html
> Sent from the Rhodes 22 mailing list archive at Nabble.com.
> __________________________________________________
> To subscribe/unsubscribe go to
> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>
> For the list Charter and help with using the mailing list and archives 
> go to http://www.rhodes22.org/list 
> __________________________________________________
>
> __________________________________________________
> To subscribe/unsubscribe go to
> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>
> For the list Charter and help with using the mailing list and archives 
> go to http://www.rhodes22.org/list 
> __________________________________________________
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 1865664 bytes
Desc: not available
Url :
http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20130917/fbf88e8
f/attachment.jpeg
__________________________________________________
To subscribe/unsubscribe go to
http://www.rhodes22.org/mailman/listinfo/rhodes22-list

For the list Charter and help with using the mailing list and archives go to
http://www.rhodes22.org/list
__________________________________________________



More information about the Rhodes22-list mailing list