[Rhodes22-list] Motor Mount

Richard Stott ric at stottarchitecture.com
Tue Jun 2 10:22:24 EDT 2020


Right, just the wood block.
I just never saw that one coming.

I tried to attache Low rez jpg files but they didn’t go  through. 
I’ll try again with PNG files . 
Let me know 

Richard Stott, AIA, LEED AP 
www.stottarchitecture.com
Office	631-283-1777
Cell		516-965-3164 





> On Jun 2, 2020, at 9:46 AM, Lowe, Rob <rlowe at vt.edu> wrote:
> 
> Ric,
> What the hell?  The whole wood block gave way and took your motor with it?  So not the entire lift but just the block attached to it?  I think you win the prize for something, but not sure what that would be.  Which lift do you have? - rob
> 
> ________________________________
> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of Steelbone <ric at stottarchitecture.com>
> Sent: Tuesday, June 2, 2020 8:58 AM
> To: rhodes22-list at rhodes22.org <rhodes22-list at rhodes22.org>
> Subject: [Rhodes22-list] Motor Mount
> 
> Launch Day always brings a surprise that you never expect. This one is was
> especially shocking.
> Departing the launch ramp, happy that the mast raising and launch went
> smoothly, I untied and left the ramp under power. The wind on the nose and
> strong ebb tide  current astern, a bridge to one side that I don't fit under
> for the first 100 yards and rocks on the right. I told my one experienced
> crew that all systems were go, but the conditions were sketchy, so if
> something went wrong, it might be scrabble to fend off bridge pilings, rocks
> or other boats.
> Less than a boat length out of the slip, I increased the power a little bit
> and the wood block of the motor mount broke off and the motor was gone.
> There was no indication of any rot visible when I repainted the block the
> day prior to launch. Normally I tie an outboard onto something so that if
> somehow it parts with the boat you don't need scuba gear to find it. I've
> learned this lesson a few times in my life, but in this case, I was secure
> in knowing that if the motor parted company with the boat, the motor mount
> lines would keep it attached. I didn't even connect the batter cables
> because the motor had started so easily with one pull, I figured I would do
> that later, when I had time.
> 
> I asked a couple of recreation divers who were on site to look for it. They
> were happy to help but inexperienced and were afraid of the currents and
> murky water at the launch site.  They tired and failed to find it.  I went
> back the next morning at slack low tide and could see the Yamaha logo in
> about 5 feet of water - jumped in and hauled it to  shallow water next to
> the floating dock and got help to haul it out.
> 
> 
> I never thought the lift system was very good and I wanted one that would
> lift the motor all the way up without having to tilt it as well.  I know the
> lift systems have changed over the years and I don't really like the
> electric lifts I have seen.  I want a longer throw manual lift.
> Stan - Can you send a replacement right away?
> If not, can anyone recommend an alternative mount - Garlick or something?
> I'm pickling the motor and hopefully it will recover from the dousing, but I
> need a new mount asap - any ideas?
> Ric
> Dadventure
> Hampton Bays
> 
> 
> 
> --
> Sent from: http://rhodes-22.1065344.n5.nabble.com/



More information about the Rhodes22-list mailing list