[Rhodes22-list] removing tabernacle

Michael D. Weisner mweisner at ebsmed.com
Tue Oct 27 15:20:18 EDT 2020


I wonder how 3M 5200 compares to adult barnacle attachment secretion which is nearly impossible to break.

Maybe Debond would work on barnacles!

Mike
s/v Wind Lass ('91)
Nissequogue River, NY

-----Original Message-----
From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of Graham Stewart
Sent: Tuesday, October 27, 2020 3:07 PM
To: 'The Rhodes 22 Email List' <rhodes22-list at rhodes22.org>
Subject: Re: [Rhodes22-list] removing tabernacle

Mark: I wouldn't even use it for the hull-deck joint. In fact I had to break the seal to remove the foredeck on my boat. I may be the only person to ever do that but still I don't think anything is permanent. 5200 and similar are incredible adhesives but if you are primarily interested in a sealant where high adhesive qualities are not the highest priority and if there is any possibility that you might want to break the bond in the future, I would always seek an alternative. 3M 4200 is a very strong adhesive but is easier to remove. 

Graham Stewart
Agile, Rodes 22, 1976
Kingston Ontario


-----Original Message-----
From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Mark Whipple
Sent: Tuesday, October 27, 2020 10:28 AM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] removing tabernacle

I've read that if you take a strong, thin wire like piano wire you can slowly cut through the 5200 (AKA Devil's Glue). Don't know if heating it would help. I've never needed to try this so if you do let us know how it goes.

About the only legit use I've heard of for 5200 is a hull-to-deck joint.
That's something that you hope you'll never have to disassemble.

Good luck,

Mark

Boston, MA

2000 R22 *Luna Mia*
1987 Nimble 30 *For Sale*
1982 Com-Pac 16 *For Sale*

On Tue, Oct 27, 2020 at 10:03 AM Graham Stewart <gstewart8 at cogeco.ca> wrote:

> Where something is adhering to fiberglass with 5200 I think a 
> sufficient whack to break the bond is likely to remove the gel coat 
> before the bond breaks. A whack might work for a metal to metal bond 
> but I would still be very careful especially for something like cast aluminum.
>
> Graham Stewart
> Agile, Rodes 22, 1976
> Kingston Ontario
>
>
> -----Original Message-----
> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On 
> Behalf Of Ric Stott
> Sent: Tuesday, October 27, 2020 8:09 AM
> To: The Rhodes 22 Email List
> Subject: Re: [Rhodes22-list] removing tabernacle
>
> Careful wack with Rubber mallet!!
> Ric
> Dadventure
>
> Sent from my iPhone
>
> > On Oct 26, 2020, at 11:43 PM, Chris Geankoplis <
> chrisgeankoplis at gmail.com> wrote:
> >
> > Hey Jesse,
> > Sounds like PL5200. Strongest stuff in the world. Just about 
> > impossible
> to
> > remove. You might make a hack saw frame but with the blade at 90 
> > degrees
> to
> > a normal one. Slowly cut between the cabin roof and tabernacle. At 
> > some point you can apply a rotational motion and should get it off.  
> > You will Have an ugly scarred area. Research to see if they have 
> > come up with a solvent for 5200. If so, use that rather than the 
> > butchery method. Good luck.
> >
> > Chris Geankoplis
> > Enosis.
> >
> >> On Mon, 26 Oct 2020 at 21:51, Jesse Shumaker <
> jesse.laten.shumaker at gmail.com>
> >> wrote:
> >>
> >> Hi, I'm attempting to remove the mast tabernacle in order to 
> >> install the Dwyer Halyard Organizer plate (part DH288).  The three 
> >> screws came out easily, but the tabernacle is still attached very 
> >> strongly with an adhesive.  I don't know what adhesive was used.  
> >> The adhesive is colored white.  I tried heating up the plate with a 
> >> soldering iron and tried to squeeze in a razor but have been unable to break the seal.
> >>
> >> I would appreciate any tips from the group on how to free the 
> >> tabernacle from the cabin top.  Thanks in advance for any advice!
> >>
> >> Jesse Shumaker
> >> S/V Zephyr
> >>
>
>



More information about the Rhodes22-list mailing list